How Can We Help?
Table of Contents

Get started with i.MX 91 SODIMM SOM Development Platform

Unpacking

Remove the Development Platform from box and place above the ESD free area. Use anti-static pad/mat with proper grounding to place the Development Platform. Also make sure that, below deliverables are received without any physical damage.

Development kit contains:

  • i.MX 91 DevKit
  • 5V,2.5A Power Supply
  • USB cable (micro-B to standard-A)
  • Wi-Fi & BT Antenna
  • Safety guidelines
Safety Guidelines
i.MX 93 SODIMM DevKit– image
WIFI and BT antenna for i.MX 93 and i.MX 91 SMARC

SAFETY GUIDELINES

i.MX 91  DevKit

WIFI & BT Antenna*

1.2-12V, Power Supply
USB OTG cable

5V, Power Supply

USB OTG cable

Get to know

i.MX 93 and i.MX 91 SODIMM SoM top view image
i.MX 93 and i.MX 91 SODIMM SoM Bottom view image

i.MX91 SODIMM SOM-Top view

i.MX91 SODIMM SOM– Bottom view

  1. Wi-Fi & BT Module
  2.  i.MX 91 SoC
  3. LPDDR4

4. eMMC
5. SODIMM Edge

i.MX 93 and 91 SODIMM Dev Kit Top image

i.MX91 SODIMM Dev Kit– Top view

  1. Power Jack
  2. Audio In/Out Jack
  3. HDMI Connector**.
  4. RTC Header
  5. Eth Jack & USB2.0 Conn.-1
  6. Eth Jack** & USB2.0 Conn.-2
  7. USB OTG Connector

8. USB Debug Conn.
9. UART Header
10. Expansion Header
11. GPIO Header
12. LVDS Back light Conn.*
13. CAN Header.

14. SODIMM Edge Conn.
15. Boot Mode switch
16. SATA Connector **
17. Reset Switch
18. Power Switch
19. Parallel Camera Conn. **

i.MX 93 and 91 SODIMM Dev Kit Bottom image

i.MX91 SODIMM Dev Kit–Bottom view

20. Mini PCIe Connector**
21. JTAG Connector

*Optional
**Not Supported

22. Resistive Touch Conn.*
23. MIPI CSI 40 Pin Conn.

24. MIPI DSI 20 Pin Conn.
25. Micro SD Connector

Boot Switch Setting

Make sure On-Board Switch (SW4) is set properly as shown below image.

i.MX 93 and 91 SODIMM Boot Switch image

SW4-Boot Selection Switch.

Table 1: Boot Media Switch Settings

i.MX 93 and 91 SODIMM Boot Switch Table image

Debug Port Setting

Connect Type-A end of USB cable to PC and Micro-B end of USB cable to Development platform’s debug Micro USB connector(J8) as shown below

i.MX 93 and 91 SODIMM Debug image

Use one of the terminal application depending on the operating system of the host machine:

Powering ON

Connect the Power supply plug to the Power connector (J2) of the DevKit as shown below and switch ON the power supply. Once power is applied to the DevKit, the power LED will glow as shown in the below image.

i.MX 93 and 91 SODIMM Power ON image

Warning:

  • Do not try to connect any other Power Supply other than supplied along with i.MX 91 DevKit.
  • Contact iWave, if power LEDs are not glowing.

Boot screen

User must go through “Software User Guide” and get familiar with software section of iW-RainboW-G50M-i.MX 91 SOM.

Operating System Support

Power is applied to the DevKit & once the boot get success, depending upon the supported Operating systems and boot loader on particular Delivery, boot messages being prompted in the terminal window as shown below. Press Enter key in terminal and done with test environment setup on particular delivery.

i.MX 93 and 91 SODIMM Command Prompt image

Command Prompt (Linux)

Copyright © 2022 iWave Systems Technologies Pvt. Ltd.